How to Loom Knit a Sphere, Cone, and Cylinder on the Universal X Loom

How to Loom Knit a Sphere, Cone, and Cylinder on the Universal X Loom!!!

You need an Universal X Loom

Each shape is worked to 48 pegs but can be worked higher. 

You will also need a looming hook and polyfil. 

Terms:

WD: Wedge Decrease: First step is to move your wedge down one notch to the next set of pegs. Then move the last set of stitches over to the wedge pegs on each side. Then knit the 2 stitches together on the wedge pegs. 

WI: Wedge Increase: Requires several steps. Twin knit the 1st wedge peg, move the stitch you just made to the previous peg. Pic 1-6. Now knit the 2 wedge pegs. Pic 7-10. Twin knit the next peg beside the wedge peg, move the stitch you just created to the 2nd wedge peg. Knit the peg beside the second wedge peg you just twin knitted. Pic 11-18. Now move your wedge up one set of pegs. Place the extra loop beside the first wedge peg onto the empty peg beside the wedge peg. Now place the extra stitch on the 2nd wedge peg on the empty peg beside the 2nd wedge peg. Pic 19-23. You have now increased by 2.

K: Flat Knit: Process of tossing bottom loop over the top loop.

K2tog: Knit 2 Stitches Together: Process of tossing 2 loops over the top working strand.

TK: Twin Knit: Pull the previous stitch back, place the working yarn in front of the peg, and put the previous stitch back as it was.

P: Purl: Process of pulling working yarn from the bottom of the stitch through to the top, take existing stitch off, and place the new stitch on

DSCO: Draw String Cast On: Weave the working yarn back and forth between the pegs, every other peg should be empty. The take the working yarn and lay it over the empty pegs and toss the pegs with loops over on the pegs with loops.

DSBO: Draw String Bind Off: Send tail through every other stitch and take the stitch off after you send the tail through. After the first round you should have half the pegs with stitches and half without. Then send the tail through the remaining stitches.

Sphere

 DSCO 24 pegs Circular

Row 1-3: K

Row 4: WI 4, and K

Row 5-7: K

Row 8: WI 4, and K

Row 9-11: K

Row 12: WI 4, and K

Row 13-18: K

Row 19: WD 4, and K

Row 20-22: K

Row 23: WD 4, and K

Row 24-26: K

Row 27: WD 4, and K

Row 28-30: K

DSBO

Stuff and close up ends. 

How to make larger. For every increase double the rows you do between your increase and decrease sections. Example here we are doing 3 increases so we will do 6 rows. Lets say you do 7 increases you would do 14 rows between your increase and decrease sections. There are always 3 rows between your decrease and increases.  

Cone

DSCO 24 pegs circular

Row 1-3: K

Row 4: WI 4, and K

Row 5-7: K

Row 8: WI 4, and K

Row 9-11: K

Row 12: WI 4, and K

Row 13: P

Row 14-28: K

Row 29: WD 4, and K

Row 30-44: K

Row 45: WD 4, and K

Row 46-60: K

Row 61: WD 4, and K

DSBO

Place in a flat foam or cardboard circle at the bottom stuff and close up top. 

General rule follow the beginning like normal, you can make larger by simply increasing more. Alway Purl 1 row before you start doing the top of the cone. If you want a sharper point at the top of your cone do 7 rows knit after the very last decrease row. If you want a fatter cone do 10 rows between decreases instead of 15 rows.

Cylinder

 DSCO 24 pegs circular

Row 1-3: K

Row 4: WI 4, and K

Row 5-7: K

Row 8: WI 4, and K

Row 9-11: K

Row 12: WI 4, and K

Row 13: P

Row 14-43: K

Row 44: P

Row 45: WD 4, and K

Row 46-48: K

Row 49: WD 4, and K

Row 50-52: K

Row 53: WD 4, and K

Row 54-56: K

DSBO

Have 2 cardboard or foam circles, put 1 circle in and stuff put the other in and close up ends. 

 You can increase or decrease more to make larger and you always do a purl after you increase and a purl row before you start to decrease. You can do however many rows you want between your purl rows. I did 30 above but you can do more or less depending on what you want. 

Useful Tips

Take the option of removing the bottom sections or top sections of these shapes or combine the shapes to create stuffed animals. You can do the sphere and when you go to decrease switch to the cone to create a head with a pointy hat. You can do the cylinder and not do the decrease section and create a body. You can also do a sphere but do a lot more rows between your increases and decreases to create a leg or arm. Have fun and create what you want using these 3 basic shapes on the X loom.